Organizational, Direct Support and General Support Maintenance Manual: Truck Tractor, Yard Type, 43,500 LB GVW, DED, 4x2, Army Model M878A1 (Ottawa Model 50) (NSN 2320-01-121-2102)DIANE Publishing - Truck tractors |
Common terms and phrases
Appendix C Item Assembly cont Automotive Repairer MOS axle bearing BODY AND CAB bushing Cab tilt capscrews cause serious injury Check Clean cloths cleaning solvent P-D-680 Common Organizational Maintenance compressed air contact with skin control valve Cotter pin cylinder damaged Disconnect double check valve engine Equipment Condition Paragraph FIFTH WHEEL front FSCM gage gasket hose inch ITEM ACTION REMARKS LOCATION ITEM ACTION LOCATION REASSEMBLY cont lock washers locknuts Lubricate medical aid immediately medical attention immediately O-ring obtain medical aid Organizational Maintenance Tool piston plate plug Position pounds foot power steering power take-off pressure proceed to step pump Rear Remove Remove Repairer MOS 63H Replace if cracked retaining ring pliers safety glasses screws seal ring sector shaft shaft snap ring Socket wrench STEP LOCATION ITEM STEP LOCATION REASSEMBLY swaging SYSTEM MAINTENANCE CONT task covers Thrust washer torque torque converter Torque wrench Tractor TRANSMISSION CONT TROUBLESHOOTING Wear protective goggles
Popular passages
Page B-18 - if applicable. e. Column 5 - Unit of Measure (U/M). Indicates the measure used in performing the actual maintenance function. This measure is expressed by a two character alphabetical abbreviation (eg, ea, in, pr). If the unit of measure differs from the unit of issue, requisition the lowest unit of issue that will satisfy your requirements.
Page B-1 - Section I. INTRODUCTION a. This section provides a general explanation of all maintenance and repair functions authorized at various maintenance categories. b. The Maintenance Allocation Chart (MAC) in section II designates overall authority and responsibility for the performance of maintenance functions on the identified end item or component. The application of the maintenance
Page B-18 - These items are authorized to you by CTA 50-970, Expendable Items (Except Medical, Class V, Repair Parts, and Heraldic Items). C-2. EXPLANATION OF COLUMNS a. Column 1 - Item Number. This number is assigned to the entry in the listing and is referenced in the
Page B-18 - to the item; use it to request or requisition the item. d. Column 4 - Description. Indicates the Federal item name and, if required, a description to identify the item. The last line for each item indicates the part number followed by the Federal Supply Code for Manufacturer (FSCM) in
Page B-1 - Calibrate. To determine and cause corrections to be made or to be adjusted on instruments or test, measuring, and diagnostic equipments used in precision measurement. Consists of comparisons of two instruments, one of which is a certified standard of known accuracy, to detect and adjust any discrepancy in the accuracy of the instrument being compared.
Page B-2 - names of components, assemblies, subassemblies, and modules for which maintenance is authorized. c. Column 3 Maintenance Function. Column 3 lists the functions to be performed on the item listed in Column 2. (For detailed explanation of these functions, see paragraph B-2.)
Page B-2 - is shown as the 3rd position code of the SMR code. i. Repair. The application of maintenance services or other maintenance actions to restore serviceability to an item by correcting specific damage, fault, malfunction, or failure in a part, subassembly, module (component or assembly),
Page B-1 - by sight, sound, or feel). b. Test. To verify serviceability by measuring the mechanical or electrical characteristics of an item and comparing those characteristics with prescribed standards. c. Service. Operations required periodically to keep an item in proper operating condition, ie, to clean
Page B-3 - order, which shall be keyed to the remarks contained in Section IV. B-4. EXPLANATION OF COLUMNS IN TOOL AND TEST EQUIPMENT REQUIREMENTS, SECTION III ~| a. Column 1 - Reference Code. The tool and test equipment reference code correlates with a code used in the MAC, Section II, Column 5. b. Column 2 - Maintenance Category. The lowest category of maintenance authorized to use the tool